View IXP220_7801510.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IXP220 software quick start guide scope of document this document gives a brief overview of the IXP220 system. document conventions we use the following conventions in this document: note C points out extra information tip C points out alternative methods to perform a task important C points out important information warning C points out potential danger to you or the product before you begin have the following available: ? an active ethernet connection (using a standard ethernet cable) to the IXP220 controller and ip terminals . ? the IXP220 software suite. ? the mac address and fixed address of each IXP220 controller C on a label bundled with the controller.
isw302 - 0 - 0 - gb - 03 august 2010 page 2 1 1 installation IXP220 software installation procedure install the IXP220 software suite on a single host pc as follows: 1. insert the IXP220 installation cd into the cd - rom drive. 2. select the install i xp220 suite option. if the cd does not start up automatically, browse the cd in windows? explorer and double - click setup.exe. 3. select english as the language option. 4. click the ok button. if no database server is present, one is installed. follow the onscreen instructions for this. 5. at the introduction screen, click next . 6. at the licence agreement screen, select the i accept the terms of the licence agreement radio button. 7. click the next button. 8. at the choose install folder screen, click next . if you change the installation directory file path, ensure that you enter text only, no spaces . figure 1 C install set menu
isw302 - 0 - 0 - gb - 03 august 2010 page 3 9. at the choose install set screen, from the install set drop - down list, make your preferred installation type selection. an install set is a collection of pre - selected applications suitable for specific scenarios. customize an install set option by selecting or de - selecting applications from the list. 10. click the next button. 11. click the install button. 12. at the install complete dialog, click the done button. by default windows? xp (sp2 and sp3) installs a firewall. t o keep this firewall, unblock the tcp ports thereby allowing functionality of the IXP220 software. continue as follows: 1. select start > control panel . 2. select the windows firewall icon. 3. in the windows firewall settings dialog, select the exceptions tab. 4. click on the add port button. 5. unblock the tcp port in the add a port dialog, by completing th e name (for example impro) and port number ( ethernet controllers use 10005 ) text boxes. 6. select the tcp radio button. 7. close the add a port dialog, by clicking the ok button. 8. at the windows firewall settings dialog, again click on the add port button. 9. set the ethernet firebird port by completing the name (for example firebird service) and port number (ethernet communication uses 3050 ). 10. select the tcp radio button. 11. close the add a port dialog, by clicking the ok button. 12. close the windows firewall settings d ialog, by clicking the ok button.
isw302 - 0 - 0 - gb - 03 august 2010 page 4 installing the firebird 2.1 database server a database server is required to host the IXP220 database. if the IXP220 suite is installed on to a single pc, the database server installs automatically. however, if more than one pc is used to host the IXP220 software, you must install the database server manually. firebird automatically prompts to install, if a previous version is not detected. 1. as any pc on the network can host the database server, select a pc to host the database server. 2. insert the i xp220 installation cd in the pcs cd - rom drive. 3. browse to the \ database \ firebird directory on the i xp220 installation cd. 4. double - click firebird.exe . 5. in the select language setup dialog, from the drop - down menu, select your preferred language . 6. click the ok button. firebird installation wizard 1. at the welcome dialog, review and follow the on - screen instruction s. 2. c lick the next button. 3. at the licence agreement dialog, select the i accept the agreement radio button. 4. click the next button. 5. review the information dialog, and then click the next button. 6. in the select destination location dialog, select the destination directory we recommend that you use the default location of c: \ program files \ firebird \ firebird_ 2 _ 1 . 7. click the next button. 8. from the drop - down menu, select the full installation of super server and development tools option. 9. at the select start m enu folder screen click next .
isw302 - 0 - 0 - gb - 03 august 2010 page 5 figure 2 C firebird select additional tasks 10. on the select additional tasks screen: ? select the use the guardian to control the server? option. ? select the run as a service? option. ? select the start firebird automatically everytime you boot up? option. ? select the Dinstall control panel applet? option. ? select the copy firebird client library to directory? option. ? select the generate client library as gds32.dll for legacy app. support? option . 11. click the next button. 12. click the install button. 13. review the information dialog and then click the next button. 14. click the finish button.
isw302 - 0 - 0 - gb - 03 august 2010 page 6 install ing the usb registration interface s usb driver IXP220 uses a usb registration reader interface to read tags. some interface versions also provide an rs485 communication link to the controllers. to install the driver, proceed as follows: if there are old usb drivers on the pc, delete them before installing the prov ided driver. on some pcs, the new hardware found wizard displays every time you plug in a usb registration reader interface with a new usb serial number (fixed address). if this happens, choose the option to automatically install the unit. the new hardware found wizard will not display again. 1. plug the usb registration interface into a usb port on the pc. the found new hardware wizard displays. 2. select the locate and install driver software (recommended) option. 3. select i dont have the disk. show me other options . 4. select the browse my computer for driver software (advanced) option. 5. click the browse button. 6. in the browse for folder dialog, select the IXP220 \ usb_device _driver folder. 7. click the ok button. 8. click the next button. 9. at the windows securit y dialog, select the install this driver software anyway option. 10. click the close button. you will notice that the wizard pops up twice, installing two drivers; one for the usb registration reader and one for the com port to usb bridge .
isw302 - 0 - 0 - gb - 03 august 2010 page 7 2 2 pre - configu ration procedure when all IXP220 software components are installed, you need to perform the pre - configuration procedure . this procedure determines if the hardware communication infrastructure is functioning correctly. rs485 communications infrastructure 1. using the supplied usb cable, connect the improx rs to the pc. 2. using the IXP220 controller s rs485 controller port, connect the IXP220 controller to the improx rs. usb communications infrastructure 1. plug the IXP220 controller into a usb port on the pc. the found new hardware wizard displays. 2. select the locate and install driver software (recommended) option. 3. select i dont have the disk. show me other options . 4. select the browse my computer for driver software (advanced) option. 5. click th e browse button. 6. in the browse for folder dialog, select the IXP220 \ usb_device _driver folder. 7. click the ok button. 8. click the next button. 9. at the windows security dialog, select the install this driver software anyway option. take note of the com port number displayed by the driver software installation dialog. 10. click the close button.
isw302 - 0 - 0 - gb - 03 august 2010 page 8 tcp/ip communications infrastructure if your installation includes ip terminals, review the section guidelines for setup of ip terminals (improx itt or itrt) on page 43 before proceeding further. f or IXP220 controllers or terminals installed on the lan (that is the local subnet of the host pc), make use of the discovery utility integrated with the IXP220 base application . for IXP220 controllers or terminals installed on a wan (that is the non - local subnet of the host pc), make use of the stand - alone discovery utility (loc al to the controller) and export the configuratio n settings to the host pc . the host pc runs the IXP220 base application. ensure the pc running discovery is on the same subnet as the IXP220 controllers or terminals for viewing. view all available IXP220 controllers or terminals on the local subnet 1. using your chosen method, open the discovery utility: ? from the IXP220 base application , from the menu bar, select hardware > unit discovery . ? alternatively, start the stand - alone discovery utility from windows? by going to start > all programs > IXP220 > utils > discovery utility . 2. on the menu bar, go to network > search local subnet . 3. if the utility fails to find any devices, at the device not found dialog, click the ok button. 4. on the menu bar, go to network > advanced local search . by selecting advanced local search , you may select the correct network interface (only displayed where more than one exists) and enter the correct subnet mask . if the search returns controller or terminal details, the utility (while running) retains the networ k interface
isw302 - 0 - 0 - gb - 03 august 2010 page 9 and subnet mask i nformation for further searches. you may however, use advanced local search again during the session for further searches using different search criteria. 5. select the relevant network interface, if more than one displays. 6. click the ok button. 7. in the input dialog, in the textbox, enter the subnet mask for your network. 8. click on the button . wait for the controllers and terminals to display. sort the information displayed in either ascending or descending order by selecting the column header . view a specific controller or terminal 1. on the menu bar, go to network > search ip . 2. in the enter ip address dialog, enter the ip address of the controller or terminal youre searching for. 3. click on the button. wait for the controller or terminal to display. secure logon 1. in the device password dialog, enter your password . the default password is masterkey , for improved security we recommend that you change this password. 2. click on the button. change the secure logon 1. from the menu bar, select configuration > change password . 2. logon if requested. 3. in the enter new password textbox enter a new password (not exceeding 16 characters) for the selected controller or terminal . 4. in the confirm new password textbox re - enter your chosen password.
isw302 - 0 - 0 - gb - 03 august 2010 page 10 5. click on t he button. grouping controllers and terminals on display of controllers and terminals, the following icons appear: the icon represents unlinked controllers. the icon represents terminals and the icon represents controllers with linked terminals. on expanding the controller tree, the icon displays, with the linked terminals displaying below. creating the group and adding controllers there is no need to give a group name to a controller if it has no ip terminals. 1. select the controller and the terminals it should control. 2. on the menu bar, select configuration > add to group . alternatively, right - click and select add to group from the pop - up menu. 3. in the enter group name dialog, enter a suitable group name for the selected units. 4. logon if requested (see page 9 ). a password is required for each controller and terminal being added to the group. 5. click the button. adding terminals to exis ting controller groups 1. select the terminal(s) to be added to the group. 2. on the menu bar, select configuration > add to group . alternatively, right - click and select add to group from the pop - up menu.
isw302 - 0 - 0 - gb - 03 august 2010 page 11 3. in the select the group name dialog, double - click on your chosen group name row. 4. logon if requested (see page 9 ). a password is required for each controller and terminal being added to the g roup. 5. click the button. communication configuration C case local configure the controller or terminal s static ip address (ethernet) figure 3 C case local configure the controller or terminal s static ip address (ethernet) if a dhcp server is present, ip addresses are dynamically assigned initially. obtain a suitable ip address from your network administrator. a private static ip address is essential for the controller or terminal because a dhcp server may assign a new ip address resulting in the software losing communications. if the controller or terminal is not on the dhcp server, ensure the pc is on the same ip range as that of the controller or terminal . if the pcs ip range differs, you cannot change the controll er or terminal s settings.
isw302 - 0 - 0 - gb - 03 august 2010 page 12 1. from the IXP220 base application, from the menu bar, select hardware > unit discovery . 2. in the discovery utility window, select the controller or terminal for configuration. 3. from the menu bar, select network > configure ip . 4. logon if requested (see page 9 ). figure 4 C configuration settings dialog by assigning an invalid ip address, the controller or terminal may no longer communicate. refer to the hardware installation manual for information on restoring factory defaults. 5. in the device ip address textbox, enter a device ip address . 6. tick the checkbox to set the ip address to static . 7. in the gateway ip address textbox, enter a gateway ip address . 8. tick the checkbox to set the gateway ip address to static . 9. continue with one of the procedures (subnet mask or subnet host bits) that follow:
isw302 - 0 - 0 - gb - 03 august 2010 page 13 subnet mask a. select the subnet mask radio button . b. in the textbox, alongside, enter the subnets address . c. tick the checkbox to set the subnet mask to static . subnet host bits a. select the subnet host bits radio button. b. enter the number of bits in the textbox. 10. if necessary, amend the supplied device name . use the same site prefix to name devices belonging to the same site. for example: Dsite _ 1 C factory, Dsite _ 1 C testing and so on. changes to the ip configuration result in the controller or terminal rebooting on acceptance of the change. the configu ration settings dialog remains open while allowing the controller or terminal to reboot. on closure of the dialog, the utility again searches for the controller or terminal and if successful, displays the updated details. 11. ensure the force update checkbox i s unchecked . if the force update checkbox remains unchecked, the controller or terminal changes the ip address testing communication on the new address. if successful, the update becomes final; if not, the controller or terminal reverts to its old settings. 12. click the update button. after detection and configuration its not necessary to assign a logical address, as the IXP220 auto - id process does this. it is not necessary to export the settings to a file.
isw302 - 0 - 0 - gb - 03 august 2010 page 14 communication confi guration C case remote option 1: configure the controller or terminal s static ip address (ethernet) figure 5 C case remote configure the controller or terminal s static ip address (ethernet) use the stand - alone discovery utility on the same local subnet as the IXP220 controllers or terminal s for configuration. you may temporarily install and pre - configure the controllers or terminals on any convenient subnet, local to the pc running the discovery utility. after configura tion, move the controllers or terminals to the remote location. alternatively install the discovery utility on a pc on the remote subnet. export the settings to a file for manual entry into the IXP220 base application. if a dhcp s erver is present, ip addresses are dynamically assigned initially. if the controller or terminal is not on the dhcp server, ensure the pc is on the same ip range as that of the controller or terminal . if the pc's ip range differs, you cannot change the c ontroller or terminal 's settings . a public static ip address is essential for the controller or terminal because the controller or terminal is destined for a wan.
isw302 - 0 - 0 - gb - 03 august 2010 page 15 1. in windows?, go to start > all programs > ixp 220 > utils>discovery utility . 2. in the discovery utility window, select the controller or terminal for configuration. 3. from the menu bar, select network > configure ip . 4. logon if requested (see page 9 ). figure 6 C configuration settings dialog by assigning an invalid ip address, the controller or terminal may no longer communicate. refer to the hardware installation manual for information on restoring factory defaults. 5. in the device ip address textbox, enter a device ip address . 6. tick the checkbox to set the ip address to static . 7. in the gateway ip address textbox, enter a gateway ip address . 8. tick the checkbox to set the ga teway ip address to static . 9. continue with one of the procedures (subnet mask or subnet host bits) that follow: subnet mask a. select the subnet mask radio button. b. in the textbox, alongside, enter the subnets address . c. tick the checkbo x to set the subnet mask to static .
isw302 - 0 - 0 - gb - 03 august 2010 page 16 subnet host bits a. select the subnet host bits radio button. b. enter the number of bits in the textbox. 10. if necessary, amend the supplied device name . use the same site prefix to name devices belonging to the same site. for example: Dsite_1 C f actory, Dsite_1 C testing and so on. if the force update checkbox remains unchecked, the controller or terminal changes the ip address testing communication o n the new address. if successful, the update becomes final; if not, the controller or terminal reverts to its old settings. changes to the ip configuration result in the controller or terminal rebooting on acceptance of the change. the configuration se ttings dialog remains open while allowing the controller or terminal to reboot. on closure of the dialog, the utility again searches for the controller or terminal and if successful, displays the updated details. 11. ensure the force update checkbox is checked when assigning an address on an external subnet . the controller or terminal changes the ip address and reboots. if the address points outside the local subnet, the controller or terminal is not found until its physically moved to the new location. 12. clic k the update button. 13. from the menu bar, select file > export ip config . 14. in the save dialog, click the save button (by default this file is named discovery.txt , you may however change this file name). 15. exit the discovery utility. 16. send a copy of the exported di scovery file ( discovery.txt ) to the host location. 17. if locally pre - configured, move the controller or terminal to its remote location.
isw302 - 0 - 0 - gb - 03 august 2010 page 17 after installing the controller or terminal in its new location, you can find it by going to network > search ip . option 2: configure the controller or terminal s public host name (ethernet) use this option where you install your IXP220 controller or terminal behind a router with a public hostname resolved to an ip address. in this scenario, the router is setup (by your network administrator) to route data to the separate controllers or terminals via the port numbers uniquely associated with them. detection of controllers or terminals using the discovery utility is only done locally, that is on the local subnet, be hind the router. to address the controller or terminal from the world beyond the router, the local ip address of the controller or terminal must change to the routers public hostname. figure 7 C case remote configure the con troller or terminal s public host name (ethernet) 1. select a unique communication port number for the IXP220 controller or terminal . 2. program the router to direct all data destined for that port to the controller or terminal .
isw302 - 0 - 0 - gb - 03 august 2010 page 18 3. in windows?, go to start > all programs > IXP220 > utils > discovery utility . 4. in the discovery utility window, select the controller or terminal for configuration. 5. from the menu bar, select network > configure ip . 6. logon if requested (see page 9 ). 7. allow the dhcp assigned addresses to remain and set as static or obtain a static address from your network administrator. 8. if necessary, amend the supplied device name . change the secure logon and clear the controller or terminal s memory as required. 9. change the communication port number to the unique port number set up on the router . 10. from the menu bar, select file > export ip config . 11. in the save dialog, click the save bu tton (by default this file is named discovery.txt , you may however change this file name according to your needs). 12. exit the discovery utility. 13. send a copy of the exported discovery file ( discovery.txt ) to the host location. in the IXP220 software now add a new communication channel to your selected site, either manually or by importing the file you exported earlier ( discovery.txt ). if the file is imported, the port number is correct and you need only change the ip address to the routers public hostname. auto - id continues as normal. option 3 a : configure the controllers mobile settings (gprs) for gprs and sms this connection option is not supported where you have controllers connected (by rs485) to the gprs enabled controller.
isw302 - 0 - 0 - gb - 03 august 2010 page 19 when configuring the gsm module for gprs and sms ensure that you obtain a public access point name (apn) from your mobile service provider. this option only applies to the IXP220 controller fitted with a gsm module. pre - configure the controller with the controller connected to the local lan. after pre - configuration, remove the network connection from the controller. pre - configuration, get the following from your mobile service provider : ? buy a sim card (you will need the pin and puk numbers fo r this sim card). ? get a public access point name ( apn ). ? confirm details for the sms service centre . ? have the username and password for the access point name (apn) available (only needed in some instances). and from a dynamic domain name service provider , get the following: ? select one of the supported providers, namely changeip.org , dyndns.com or no - ip.com . ? register a hostname for your IXP220 controller with your chosen provider. ? register a username and password for your IXP220 controller. ? register a hostn ame for the pc hosting the IXP220 software , or use a public static ip address. both hostnames must resolve to a public ip address, they cannot remain blank.
isw302 - 0 - 0 - gb - 03 august 2010 page 20 1. in windows?, go to start > all programs > IXP220 > utils > discovery utility . 2. in the 220 discovery utility window, select the controller for configuration. 3. from the menu bar, select network > configure mobile settings . 4. logon if requested (see page 9 ). figure 8 C configure mobile settings dialog the signal strength icon on the status bar indicates the signal strength being experienced by the controllers gsm module. 5 bars indicates maximum signal strength.
isw302 - 0 - 0 - gb - 03 august 2010 page 21 5. complete the fields under the header mobile service provider : ? sim pin this is the personal identification number (pin), a numerical combination of up to 5 digits, supplied with your sim card. wrong entry of the pin (more than 3 times) locks the sim card. ? sim puk this is the pin unlock key. this number offers protection of the device and sim card with the pin. entry of the wrong puk (more than 10 times) permanently blocks the device, a new sim card is then required. ? sms service centre the contact number for the repository that stores messages for delivery to the des tination user when they are available. stored on the sim card, this number may not come into sight until you activate your mobile settings. if you wish to use the service and the number does not finally appear, contact your service provider for assistanc e ? access point name (apn) this is the name used to identify a public (free) gprs bearer service in the gsm mobile network. the access point name (apn) defines the type of service provided in the packet data connection. ? apn username possibly needed for the access point name (apn). ? apn password possibly needed for the access point name (apn). 6. ensure the configure for gprs and sms radio button is selected (default). 7. under the header dynamic domain name service , from the dynamic dns provider drop - dow n list, select one of the supported providers. 8. in the dynamic dns hostname textbox, enter the registered IXP220 controllers hostname. 9. in the dynamic dns username textbox and dynamic dns password textbox, enter the registered username and password respecti vely for your IXP220 controller.
isw302 - 0 - 0 - gb - 03 august 2010 page 22 10. in the host pc hostname or ip address textbox, enter the registered hostname for the pc hosting the IXP220 software; alternatively, enter the public static ip address. 11. click the apply button. the discovery utility captur es the configuration information and forwards the information on to the controller for activation. the controller starts the process of establishing a gprs connection. the discovery utility queries the controller for status until the utility gets a resul t. during the verification process there is an approximately 60 - second time - out. the discovery utility decides on the success of the configuration. at the end of the verification process, the status bar at the bottom of the configure mobile settings dialog, displays the status of the configuration. possible status messages include: ? listening this is the desired status message. ? gsm module not present indicates the gsm module is removed or uninstalled. ? gsm module present controller is aware the gsm module is connected, however the controller is busy going through the connection process. ? sim pin or puk error indicates you have captured the wrong pin or puk number. ? gprs network error indicates the gsm module cannot connect to the network. ? apn error indicates the wrong apn name was captured. this message also appears however, where you have exceeded your data cap or you have no available airtime on your sim card. ? ddns error indicates there is an error with the captured dd ns parameters.
isw302 - 0 - 0 - gb - 03 august 2010 page 23 ? connected connected status only occurs if a controller was already configured and currently connected by gprs to the IXP220 software while still connected by ethernet. if the connection is not established, the controller may begin the verification process again. in an instance where the verification process times out, click the query status button manually requesting the status. if you do not get the status listening , correct any errors and then press the apply button again. on acceptance of the settings, the gprs parameters are written to the discoverygsm.txt file. the IXP220 software automatically imports this file for permanent storage in the database (i n case of hardware replacement). 12. on achieving the listening status, close the configure mobile settings dialog. 13. export the configuration file, from the menu bar, select file > export ip config . 14. click the save button. 15. exit the 220 discovery utility. 16. send bot h the discoverygsm.txt and discovery.txt files to the host pc (ensuring you place both files in the same destination folder) before beginning the auto - id process. 17. disconnect the IXP220 controller from the lan . 18. reboot the controller. 19. continue with the aut o - id process (see page 27 for assistance ) . option 3b: configure the controllers mobile settings (gprs) for sms only a public access point name (apn) is not required for sms only.
isw302 - 0 - 0 - gb - 03 august 2010 page 24 in instances where your controller connects by ethernet, but you still require sms capability, continue as follows: figure 9 C configure mobile settings dialog the signal strength icon on the status bar indicates the signal strength being experienced by the controllers gsm module. 5 bars indicates maximum signal strength. 1. in windows ? , go to start > all programs > IXP220 > utils > discovery utility . 2. in the 220 discovery utility window , select the controller for configuration. 3. from the menu bar, select network > configure mobile settings . 4. logon if requested (see page 9 ). 5. ensure the configure f or sms only radio button is selected. 6. complete the fields under the header mobile service provider : ? sim pin ? sim puk ? sms service centre 7. click the apply button. your setup is complete and working correctly when you receive the status message sms confi guration completed . we recommend that you test the connection by clicking the test sms button. where called for by your country and or your service provider, precede the recipients mobile number with the country code.
isw302 - 0 - 0 - gb - 03 august 2010 page 25 configure the port number this is an advanced feature; use the feature only if required. after making changes to one or more controller or terminal s configuration settings, ensure that you export the configuration file for entry into the IXP220 base application. using the discovery utility, view or configure the port number of the controller or terminal as follows: 1. select the controller or terminal for configuration. 2. from the menu bar, select configuration > set configuration . 3. logon if requested (see page 9 ). 4. in the communication port number textbox, change the port number. the default port number is 10005 for controllers and 10008 for terminals . only change the default p ort number if it clashes with other devices or services on your network. 5. in the terminal listener port textbox, change the port number (controller listens to terminals on this port). the default port number is 10008 . only change the default port number if it clashes with other devices or services on your network or if you communicate with the terminal over a wan using port fowarding. 6. tick the safe ip checkbox, thus ensuring that the controller only responds to the host pc. 7. click the button to confirm. 8. wait while the controller or terminal re - boots (about 15 seconds).
isw302 - 0 - 0 - gb - 03 august 2010 page 26 3 3 site configuration procedure open the software figure 10 C login dialog 1. in windows?, click start > all programs > IXP220 > IXP220 . 2. enter your username ( sysdba ) and password ( masterkey ). 3. from the security device search drop - down list, make your selection from the following choices: ? automatically search for IXP220 - 3 and IXP220 - 4 installations where an improx rs is connected but you are unsure of the com port numb er in use by the improx rs. automatically searching on a computer that has an enabled bluetooth or infrared port may result in the IXP220 application freezing. ? enter the com port name for IXP220 - 3 and IXP220 - 4 installations where an improx rs is connect ed and you know the com port number in use by the improx rs. recommended when you have an enabled bluetooth or infrared
isw302 - 0 - 0 - gb - 03 august 2010 page 27 port . if you select this choice, enter the com port number in the supplied textbox. if your installation does not use the default dat abase server port of 3050, enter the server name and port number (that is server:port ). an example could include localhost:3051 , that is with 3051 being the port used. ? i do not have one for IXP220 - 1 and IXP220 - 2 installations with no improx rs. 4. click the button. do not disconnect the improx rs while still connected to the IXP220 software. should you unintentionally disconnect the improx rs while the softwares running, close the IXP220 software, reconnect the improx rs and then restart the software. database version check after completing the login action, the automatic database upgrade utility checks the database version. if the utility confirms the database is older than that needed by the software, a warning dialog tells you an upgrade is needed . perform the upgrade as follows: 1. at the warning dialog, click the ok button. 2. in the database updater dialog, click the upgrade button. 3. at the message dialog, click the ok button. if you do not upgrade the database immediately, the IXP220 software closes. hardware auto - id hardware detected for the first time receives a logical address. this logical address does not change, thus ensuring continuity in the database.
isw302 - 0 - 0 - gb - 03 august 2010 page 28 during an auto - id, the base application searches for and configures improx hard ware for use with the IXP220 system. after physically connecting and powering up the hardware, perform the following steps: 1. at the auto - id is recommended for new sites dialog, click the yes button. 2. at the confirm auto - id dialog, click the ok button. 3. the auto - id process differs for different communications mediums, therefore continue with one of the following: controller connected to host pc using rs485 (improx rs) from the auto id communications configuration dialog, select the appropriate com port record. controller connected to the host pc using tcp/ip if your controller does not appear in the auto - id communications configuration dialog continue as follows: when using ip terminals, do not use the button. instead, make use of the button a. click the button. b. in the channel column, replace the default ip address details with the ip address of your controller. c. press enter . or alternatively continue as follows: a. click the button. b. in the input dialog, enter the subnet mask details for your network. c. click the button.
isw302 - 0 - 0 - gb - 03 august 2010 page 29 the ip door controllers (advanced) tab provides a list o f the ip terminals i n the system as well as the ip a ddress of the controllers they connect to. when using ip terminals over a wan, chan ge the controller ip a ddress to the ip a ddress of the router to ensure that the ip terminal communicates correctly. to do this, continue as follows: 1. on the auto - id channel tab, click the button. 2. in the input dialog, enter the subnet mask det a i ls for your network. 3. click the button. 4. select the ip door controllers (advanced) tab. 5. in the address column, enter the public stat ic ip address of the router the controller will use to communicate with the terminal. 6. in the respond to address column, enter the public static ip address o f the router the terminal will use to communicate with the controller. 7. if necessary, edit the additional timeout (0.1s) value. 8. continue with auto - id as normal. (see s tep 4 following ). controller connected over a wide area network (wan) controllers connected using a gsm module do not support ip terminals. a. click the import channels button. b. select the discovery.txt fil e (originally exported from the discovery utility). c. click the open button.
isw302 - 0 - 0 - gb - 03 august 2010 page 30 the ip door controllers (advanced) tab provides a list o f the ip terminals i n the system as well as the ip a ddress of the controllers they connect to. when using ip terminals over a wan, change the controller ip address to the ip a ddress of the router to ensure that the ip terminal communicates correctly. to do this, continue as follows: 1. on the auto - id channel tab, click the import channels button. 2. select the discovery.txt file (orignally export from the discovery utility). 3. click the open button. 4. select the ip door controllers (advanced) tab. 5. in the address column, enter the public static ip address of the router the controller will use to communicate with the terminal. 6. in the respond to address column, enter the public static ip address of the router the terminal will use to communicate with the controller. 7. if necessary, edit the additional timeout (0.1s) value. 8. continue with auto - id as normal. (see step 4 below ). 4. from the list of devices displayed, in the auto - id channel column, make your selection. 5. click the button. you may carry out the auto - id process at any stage, by selecting hardware > auto id units . connecting controller a via the network and controller b (connected to controller a) by rs485, lets you configure both controllers at the same time.
isw302 - 0 - 0 - gb - 03 august 2010 page 3 1 after performing auto - id, review the log of identified units by selecting hardware > latest auto id log from the menu bar. this feature lets you check whether auto - id has missed any terminals, possibly because of a wrong dip - switch setting or faulty communications. firmware version confirmation after physically connecting, powering up and identifying the improx hardware, confirm whether a firmware upgrade is required. the firmware revisions dialog indicates the unit type along with the latest firmware revision available and the current firmwar e version in use by the unit. access the firmware revisions dialog by selecting hardware > firmware version check from the menu bar. see the software installers gu ide, part 7 C utilities for m ore information on the firmware upgrade utility . configur ing the site standard site configuration 1. if not already selected, select the page tab. 2. in the configuration pane, complete the site name textbox. 3. complete the site street/physical address text area. advanced site configuration communications group options 1. if you wish to communicate only with the selected site, select the communicate exclusively checkbox. 2. from the communication schedule drop - down list select a communication schedule.
isw302 - 0 - 0 - gb - 03 august 2010 page 32 3. in the final drop - down list in the communications group, select from the fo llowing options: ? inter - controller this allows for communication to take place across controllers. inter - controller communications is beneficial when used with building management and in maintaining anti - passback (apb) status across controllers. ? fall - back this allows for configuration where tcp/ip is the default communications channel and rs485 being the secondary channel. where your tcp/ip connection fails, the IXP220 software falls back on rs485 and operations continue as normal (slightly slower than tcp /ip). when the tcp/ip connection restores, the software automatically resumes communication on the primary tcp/ip connection. this configuration does not support inter - controller or pass - through communications. the selection you make above, determines the options available to you on the controller configuration pane. click the synchronize button to write ip mapping files to the IXP220 directory. these files are used on selection of udp multi controller as the communications type . region group options 1. from the time zone drop - down list, make your selection. 2. set the apply daylight saving option as follows: a. alongside apply daylight saving , click the yes radio button. b. click on the set daylight saving button. c. in the set daylight saving dialog, set the time offset, start date, start time, end date and end time. d. click the button.
isw302 - 0 - 0 - gb - 03 august 2010 page 33 miscellaneous group options door status polling 1. click the set parameters button. ? set the polling frequency (seconds) how often doors (locations) get polled for their status. ? set the door open time limit (seconds) normal duration doors (locations) remain open. 2. click the button. valid site codes 1. c lick the configure button. figure 11 C site code configuration 2. click the button. 3. in the site code textbox, enter a suitable code. 4. select either the append to exiting codes or overwrite existing codes radio button. 5. click the button. after updating the site configuration pane, click the button. controller configuration 1. select the page tab.
isw302 - 0 - 0 - gb - 03 august 2010 page 34 2. in the controller name textbox, assign your controller a suitable name. 3. from the mode configuration drop - down list, make your selection. the instructions that follow continue as for an advanced configuration. for a standard configuration ignore references made to fields that appear greyed out. 4. enable or disable controllers as per your requirements, by selecting or de - selecting the co ntroller enabled checkbox. 5. from the apb configuration group, adjust the following settings: ? set the apb lockout delay on entry (minutes) the same tagholder may not pass the same anti - passback (apb) entry access point within the specified time period. ? set the apb lockout delay on exit (minutes) the same tagholder may not pass the same anti - passback (apb) exit access point within the specified time period. site configuration set to inter - controller communications with your site setup to use inter - controller communications, continue with the following controller configuration options: 1. from the primary communications drop - down list, make your selection. 2. from the communications mode drop - down list, make your selection from the following choic es: ? standard controller this is the default choice. this configuration associates to controller configurations preceding v1.82, including all configuration choices offered in IXP220 software v1.80. in addition, support includes inter - controller communica tions (for ip controllers only). ? controller forwards communications for rs485 controllers this allows for inter - controller communications for controllers daisy - chained from an ip controller. for example, controller a has a network cable connected to it an d has
isw302 - 0 - 0 - gb - 03 august 2010 page 35 controller b and controller c connected to its rs485 controller bus. a tagholder enters a door (location) on controller a, controller a will update the anti - passback status of the tagholder on controller b and controller c. this option does not af fect pass through communications. the software still communicates with the daisy - chained controllers via controller a. activate the controller forwards communications for rs485 controllers option as follows: 1. in the controller configuration pane, cli ck the communications button. 2. click the button. 3. in the address column of the new record, enter the communication port details for your improx rs. 4. click the button. 5. from the communications mode drop - down, select the controller forwards communications for rs485 controllers option. 6. from the primary communications drop - down list, select the newly added communication port number. site configuration set to fall - back communications fall - back communications allows for configuration using tcp/ip as the prima ry communications channel and rs485 as the secondary channel . where your tcp/ip connection fails, the IXP220 software falls back on rs485 and operations continue as normal (slightly slower than tcp/ip). when the tcp/ip connection restores, the software a utomatically resumes communication on the primary tcp/ip connection. this configuration does not support inter - controller or pass - through communications. with your site setup to use fall - back communications, continue with the following controller configuration options:
isw302 - 0 - 0 - gb - 03 august 2010 page 36 1. from the primary communications drop - down list, make your selection. 2. from the secondary communications drop - down list, make your select ion. after updating the controller configuration pane, click the button.
isw302 - 0 - 0 - gb - 03 august 2010 page 37 4 4 using the IXP220 software IXP220 user interface figure 12 C IXP220 base application user interface the IXP220 base application only displays as shown in figure 12 where you select the standard windows? 7 (professional, enterprise or ultimate), window s ? vista (business or ultimate) and xp professional themes . using other non - standard themes results in IXP220 displaying incorrectly.
isw302 - 0 - 0 - gb - 03 august 2010 page 38 the following parts comprise the IXP220 base applications interface: a menu bar c ontains drop - down menus that let you navigate between different operations in the IXP220 base application. these menus include: file, hardware, configuration, tagholder, web and help topics. b page tabs s witch es between the different configuration settings, for example: ? site confi guration ? controller configuration ? door configuration ? access group configuration ? tagholder configuration ? holiday configuration ? notification configuration c configuration pane l ets you adjust various settings based on your selection from the page tabs or menu bar. d viewer pane the viewer pane consists of tabs showing the following information: ? transaction viewer gives a live real - time view of all types of transactions in the system. it displays the names of the doors (locations) and details of tagholders who have entered or exited these doors (locations). ? alarm transaction viewer gives a live real - time view of all alarm transactions in the system. it displays the names of the doors (locations) and details of tagholders who have entered or exited these doors (locations).
isw302 - 0 - 0 - gb - 03 august 2010 page 39 ? communications status viewer indicates the status of the IXP220 controllers communicating with the IXP220 system. ? door status viewer indicates the status of the doors (locations) forming part of the site. you may physically unlock doors (locations) displayed here, using the IXP220 software. click the button (placed alongside the page tabs) to adj ust the base applications layout: ? first click c loses the viewer pane, opening the configuration pane in full screen mode. ? second click o pens the viewer pane in full screen mode. ? third click r eturns the base application to split - screen mode, showing both the configuration pane and the viewer pane. alternatively, adjust the layout as follows: 1. from the main menu, select view . 2. make your selection from the following: ? split view shows both the configuration pane and the viewer pane. ? configuration view closes the viewer pane, opening the configuration pane in full screen mode. ? monitoring view opens the viewer pane in full screen mode.
isw302 - 0 - 0 - gb - 03 august 2010 page 40 using help the context sensitive webhelp provided with the IXP220 software works with your positioned mouse pointer (or cursor) on your screen . for example if you place your mouse pointer in the viewer pane, webhelp opens context sensitive webhelp specific to the viewer pane. if, however, you want webhelp specific to the active configuration pane, continue as follows: 1. mo ve your mouse pointer into the configuration pane. 2. anchor your mouse pointer by clicking the left - hand button on your mouse, thus ensuring the pane has focus. 3. press the f1 key on your keyboard. the i xp220 system has integrated context sensitive webhelp. information not covered here is cov ered in detail in the webhelp. a ctivate the webhelp as follows: 1. in windows ? , go to start > programs > IXP220 > IXP220 . 2. from the menu bar select help topics > online help . key assist selecting the key assist option opens an area on the right - hand side of the base applications desktop. this area displays a list of keyboard shortcuts that let you quickly move between the page tabs. the final option listed in the key assist area ( system navigation ) opens the system navigation dialog. this dialog allows quick navigation through system related functions. . s upport diagnostics the support diagnostics bundle assists you by supplying technical support staff with information about your system. this helps them to
isw302 - 0 - 0 - gb - 03 august 2010 page 41 solve your problems quickly and efficiently. create a support diagnostic bundle as follows: 1. from the main menu, select help topics > support diagnostics . 2. select the included in bundle tab. 3. the diagnostics bundle includes the following information by defa ult. customize the information sent by deselecting the checkbox alongside: ? transactions (last 500) selecting this sends the last 500 transaction s in the system including access, status and alarm transactions. ? system log files sends the system log files. ? f irebird log (database server) sends the database server log if the database is installed on the default directory. ? site summary includes information such as the number of tagholders with access and the numbe r of doors configured on a site. also provides h ardware configuration data like how the base application communicates to the controller as well as information about connected terminals and their configuration. ? holiday data sends information about holiday configuration. ? host pc information includes information such as pc specifications, processes running on the pc and results from a netstat ( a command - line tool providing information on network connections, routing and other network interface statistics). 4. select the contact information tab. 5. fill in your contact information as necessary. 6. create the diagnostic bundle using one of the following methods: sites with pre - configured notifications for e - mail setup information please refer to part 3 - preference configuration (system notification tab). 1. click the generate bundle button.
isw302 - 0 - 0 - gb - 03 august 2010 page 42 2. if you have an existing reference number, complete the reference no . textbox. 3. complete the support e - mail addr ess textbox. 4. click the e - mail bundle button. 5. click the button. sites without pre - configured notifications 1. click the generate bundle button. 2. click the button. 3. browse to c: \ IXP220 . 4. locate the zip f ile diagnosticbundle_(date generated)_(time generated) . 5. attach the zip f ile to an e - mail. 6. send the e - mail to the technical support staff. site setup perform site setup in the following order: 1. site configuration 2. controller configuration 3. door configuration 4. access group configuration 5. tagholder co nfiguration 6. holiday configuration 7. full upload for detailed information on site setup, please refer to part 3 of the i xp220 software manual . or alternatively, refer to the webhelp included with the i xp220 software.
isw302 - 0 - 0 - gb - 03 august 2010 page 43 advanced options guidelines for the setup of ip terminals (improx itt or itrt) support for ip terminals (improx itt and itrt) is only available on controllers with firmware v 4 .0 0 and above. do not connect rs485 terminals to ip terminals on the rs485 connector. this is an unsupported configuratio n. use the discovery utility for discovering, configuring and grouping ip terminals with their parent controller. controllers must know which terminal they should communicate with. in an rs485 environment a logical address, assigned during auto - id ach ieved this. IXP220 howe ver, calls for extra steps when using an ethernet configuration. in an ethernet configuration, group ip terminals with a parent controller before configuration . then auto - id the hardware and finally, perform a full upload. only then can you access the hardware with the firmware upgrade utility. where you have more than one site, repeat the procedure for each site. steps to discover, group and configure contr oller and ip terminal settings 1. display controllers and ip terminals by performing a network search. on display of the controllers and terminals, the following icons appear: the icon represents unlinked controllers. the icon represents terminals.
isw302 - 0 - 0 - gb - 03 august 2010 page 44 2. c onfigure the ip address for each controller and ip terminal. refer to p age 11 for more information. 3. group one or more ip terminal s with a single controller. ref er to page 10 for more information. 4. configure the application settings (that is the port number ) for each controller and ip terminal. defaults should meet most in stallations needs. do not set safe ip at this stage. 5. set the password for each controller and ip terminal, ensuring that you keep the same password for all units. the default password is masterkey . change this password to a string of not more than 16 characters. 6. if you are connecting over a wan, e xport the selected units to a text file (discovery.txt). refer to page 15 for information on this process. steps required in the IXP220 base application 1. perform and auto - i d. refer to page 27 for more information. 2. perform a full upload to all units. refer to part 3 C general configuration for more information on this process. steps r e quired in the firmware upgrade utility perform a full upload before trying to ping your ip terminals. 1. start the firmware upgrade utility and set the protocol to udp multi controller . 2. check that all hardware is connected and working as specifie d by using the ping tool. 3. carry out a firmware upgrade if required.
isw302 - 0 - 0 - gb - 03 august 2010 page 45 refer to part 7 C utilities for detailed instructions on using the firmware upgrade utility. additional options ? carry out safe ip by going back to the discovery utility. search for the units and then carry out safe ip on each unit individually . refer to part 7 C utilities for more information. ? move an ip terminal from one controller to another, in the base application, uninstall th e ip terminal first. then perform a full upload. this releases the ip terminal from its parent controller and prevents network diagnostic problems. refer to part 3 C general configuration for more information.
isw302 - 0 - 0 - gb - 03 august 2010 page 46 extra information further information is available at the following resources: ? IXP220 software manual ( isw300 - 0 - 0 - gb - xx) . ? IXP220 webhelp (isw390 - 0 - 0 - gb - xx). ? IXP220 software product specification catalogue (isw350 - 0 - 0 - gb - xx). ? improx IXP220 controller product specification catalogue (isc350 - 0 - 0 - gb - xx). ? improx IXP220 controller installation manual (isc300 - 0 - 0 - gb - xx). the referenced documents are available for download at www.impro.net . alternatively, contact your impro dealer for a copy. user notes
isw302 - 0 - 0 - gb - 03 august 2010 page 47 user notes
isw302 - 0 - 0 - gb - 03 august 2010 page 48 user notes this manual is applicable to the IXP220 software suite v 1. 8 4 (upwards) . (the last two digits of the impro stock code indicate the issue status of the product). isw302 - 0 - 0 - gb - 0 3 issue 0 4 aug 2010 IXP220 \ software \ english manuals branded \ latest issue \ 220 qsg - swm b - en - 0 4 .doc x

▲Up To Search▲

Price & Availability of IXP220

	To Download IXP220 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .